Microbial induced wettability alteration with implications for Underground Hydrogen Storage.

Characterization of the microbial activity impacts on transport and storage of hydrogen is a crucial aspect of successful Underground Hydrogen Storage (UHS). Microbes can use hydrogen for their metabolism, which can then lead to formation of biofilms. Biofilms can potentially alter the wettability of the system and, consequently, impact the flow dynamics and trapping mechanisms in the reservoir. In this study, we investigate the impact of microbial activity on wettability of the hydrogen/brine/rock system, using the captive-bubble cell experimental approach. Apparent contact angles are measured for bubbles of pure hydrogen in contact with a solid surface inside a cell filled with living brine which contains sulphate reducing microbes. To investigate the impact of surface roughness, two different solid samples are used: a "rough" Bentheimer Sandstone sample and a "smooth" pure Quartz sample. It is found that, in systems where buoyancy and interfacial forces are the main acting forces, the impact of biofilm formation on the apparent contact angle highly depends on the surface roughness. For the "rough" Bentheimer sandstone, the apparent contact angle was unchanged by biofilm formation, while for the smooth pure Quartz sample the apparent contact angle decreased significantly, making the system more water-wet. This decrease in apparent contact angle is in contrast with an earlier study present in the literature where a significant increase in contact angle due to microbial activity was reported. The wettability of the biofilm is mainly determined by the consistency of the Extracellular Polymeric Substances (EPS) which depends on the growth conditions in the system. Therefore, to determine the impact of microbial activity on the wettability during UHS will require accurate replication of the reservoir conditions including surface roughness, chemical composition of the brine, the microbial community, as well as temperature, pressure and pH-value conditions.

Adsorption-desorption of 241Am(â ¢) on montmorillonite colloids and quartz sand: Effects of pH, ionic strength, colloid concentration and grain size.

Clay colloids in the subsurface environment have a strong adsorption capacity for radionuclides, and the mobile colloids will carry the nuclides for migration, which would promote the movability of radionuclides in the groundwater environment and pose a threat to the ecosphere. The investigations of the adsorption/desorption behaviors of radionuclides in colloids and porous media are significant for the evaluation of the geological disposal of radioactive wastes. To illustrate the adsorption/desorption behaviors of 241Am(Ⅲ) in Na-montmorillonite colloid and/or quartz sand systems at different pH (5, 7 and 9), ionic strengths (0, 0.1 and 5 mM), colloid concentrations (300 and 900 mg/L), nuclide concentrations (500, 800, 1100 and 1400 Bq/mL) and grain sizes (40 and 60 mesh), a series of batch sorption-desorption experiments were conducted. Combining the analysis of the physical and chemical properties of Na-montmorillonite with the Freundlich model, the influencing mechanism of different controlling factors is discussed. The experimental results show that the adsorption/desorption behaviors of 241Am(Ⅲ) in Na-montmorillonite colloid and/or quartz sand strongly are influenced by the pH value and ionic strength of a solution, the colloid concentration as well as quartz sand grain size. The adsorption and desorption isotherms within all the experimental conditions could be well-fitted by the Freundlich model and the correlation coefficients (R2) are bigger than 0.9. With the increase in pH, the adsorption partition coefficient (Kd) at 241Am(Ⅲ)-Na-montmorillonite colloid two-phase system and 241Am(Ⅲ)-Na-montmorillonite colloid-quartz sand three-phase system presents a trend which increases firstly followed by decreasing, due to the changes in the morphology of Am with pH. The Kd of 241Am(Ⅲ) adsorption on montmorillonite colloid and quartz sand decreases with increasing in ionic strength, which is mainly attributed to the competitive adsorption, surface complexation and the reduction of surface zeta potential. Additionally, the Kd increases with increasing colloid concentrations because of the increase in adsorption sites. When the mean grain diameter changes from 0.45 to 0.3 mm, the adsorption variation trends of 241Am(Ⅲ) remain basically unchanged. The research results obtained in this work are meaningful and helpful in understanding the migration behaviors of radionuclides in the underground environment.

[Australia's engineered stone ban. A sound decision]. / La prohibición de los aglomerados de cuarzo en Australia, una decisión modélica.

Australia se convirtió en diciembre de 2023 en el primer país en prohibir el uso de los aglomerados de cuarzo. El consumo de estos materiales sintéticos, que contienen más del 80% de sílice cristalina y que desde los años 90 se han empleado para la fabricación de encimeras de cocina y baños, ha contribuido al resurgimiento en numerosos países de formas aceleradas de silicosis y a una notable incidencia de enfermedades sistémicas. El objeto de este trabajo es analizar los fundamentos que sustentan la decisión australiana. Dichos fundamentos están principalmente recogidos en el informe elaborado en 2023 por la agencia gubernamental Safe Work Australia (SWA), que recomendó la prohibición del producto. SWA llevó a cabo una consulta pública entre todos los actores sociales y científicos interesados en el problema. El informe de SWA señaló la ausencia de evidencia científica sobre un umbral de sílice toxicológicamente seguro cuestionando la estrategia de los fabricantes del material de presentar como productos seguros a los aglomerados con menos del 40% de contenido de sílice. La recomendación de SWA tomó en consideración la evaluación del nivel de cumplimiento de las estrictas medidas de prevención implementadas entre 2019 y 2023, constatando que el incumplimiento siguió siendo generalizado en el sector. Además se realizó un análisis coste-beneficio para valorar el número de casos de silicosis que sería necesario evitar para "compensar" los costes económicos asociados a cada opción de prohibición. Para ello empleó el Valor Estadístico de la Vida (VEV) actualizado en 2023 en Australia y estimó en 4,9 millones de dólares australianos cada vida salvada y silicosis evitada. En nuestra opinión, la prohibición australiana es modélica por la forma en que se ha gestado la decisión, por su sólida fundamentación científica y socio-laboral, y por la aplicación del principio de precaución.

Transport and retention of ciprofloxacin with presence of multi-walled carbon nanotubes in the saturated porous media: impacts of ionic strength and cation types.

The environmental fate and risks of ciprofloxacin (CIP) in the subsurface have raised intensive concerns. Herein, the transport behaviors of CIP in both saturated quartz sand and sand/multi-walled carbon nanotubes (MWCNTs) mixtures under different solution ionic strength of the solution and coexisting cation types were investigated. Batch adsorption experiments highlighted growing adsorptive capacity for CIP with the increasing content of MWCNTs in the MWCNTs-quartz sand mixtures (from 0.5% to 1.5%, w/w). Breakthrough curves (BTCs) of CIP in the MWCNTs-quartz sand mixtures were well fitted by the two-site chemical nonequilibrium model (R2 > 0.833). The estimated retardation factors for CIP increased from 9.68 to 282 with growing content of MWCNTs in the sand column, suggesting the presence of MWCNTs significantly inhibited the transport of CIP in saturated porous media. Moreover, the values of retardation factors are negatively correlated with the ionic strength and higher ionic strength could facilitate the transport of CIP in the saturated porous media. Compared with monovalent cations (Na+), the presence of divalent cations (Ca2+) significantly facilitated the transport of CIP in the columns due to the complexation between CIP and Ca2+ as well as deposition of MWCNTs aggregates on the sand surface. Results regarding CIP retention in columns indicated that MWCNTs could enhance the accumulation of CIP in the layers close to the influent of sand columns, while they could hinder upward transport of CIP to the effluent. This study improves our understanding for transport behaviors and environmental risk assessments of CIP in the saturated porous media with MWCNTs.

Respirable dust and crystalline silica concentrations among workers at a brick kiln in Bhaktapur, Nepal.

Exposure to respirable dust and crystalline silica (SiO2) has been linked to chronic obstructive pulmonary disease, silicosis, cancer, heart disease, and other respiratory diseases. Relatively few studies have measured respirable dust and SiO2 concentrations among workers at brick kilns in low- and middle-income countries. The purpose of this study was to measure personal breathing zone (PBZ) respirable dust and SiO2 concentrations among workers at one brick kiln in Bhaktapur, Nepal. A cross-sectional study was conducted among 49 workers in five job categories: administration, fire master, green (unfired) brick hand molder, green brick machine molder, and top loader. PBZ air samples were collected from each worker following Methods 0600 (respirable dust) and 7500 (respirable crystalline SiO2: cristobalite, quartz, tridymite) of the U.S. National Institute for Occupational Safety and Health. Eight-hour time-weighted average (TWA) respirable dust and quartz concentrations were also calculated. SiO2 percentage was measured in one bulk sample each of wet clay, the release agent used by green brick hand molders, and top coat soil at the brick kiln. The geometric mean (GM) sample and TWA respirable dust concentrations were 0.20 (95% confidence interval [CI]: 0.16, 0.27) and 0.12 (95% CI: 0.09, 0.16) mg/m3, respectively. GM sample and TWA quartz concentrations were 15.28 (95% CI: 11.11, 21.02) and 8.60 (95% CI: 5.99, 12.34) µg/m3, respectively. Job category was significantly associated with GM sample and TWA respirable dust and quartz concentrations (all p < 0.0001). Top loaders had the highest GM sample and TWA respirable dust concentrations of 1.49 and 0.99 mg/m3, respectively. Top loaders also had the highest GM sample and TWA quartz concentrations of 173.08 and 114.39 µg/m3, respectively. Quartz percentages in bulk samples were 16%-27%. Interventions including using wet methods to reduce dust generation, administrative controls, personal protective equipment, and education and training should be implemented to reduce brick kiln worker exposures to respirable dust and SiO2.

Shear Bond Strength to Enamel, Mechanical Properties and Cellular Studies of Fiber-Reinforced Composites Modified by Depositing SiO2 Nanofilms on Quartz Fibers via Atomic Layer Deposition.

Introduction: Poor interfacial bonding between the fibers and resin matrix in fiber-reinforced composites (FRCs) is a significant drawback of the composites. To enhance the mechanical properties of FRC, fibers were modified by depositing SiO2 nanofilms via the atomic layer deposition (ALD) technique. This study aims to evaluate the effect of ALD treatment of the fibers on the mechanical properties of the FRCs. Methods: The quartz fibers were modified by depositing different cycles (50, 100, 200, and 400) of SiO2 nanofilms via the ALD technique and FRCs were proposed from the modified fibers. The morphologies, surface characterizations of nanofilms, mechanical properties, and cytocompatibility of FRCs were systematically investigated. Moreover, the shear bond strength (SBS) of FRCs to human enamel was also evaluated. Results: The SEM and SE results showed that the ALD-deposited SiO2 nanofilms have good conformality and homogeneity. According to the results of FTIR and TGA, SiO2 nanofilms and quartz fiber surfaces had good chemical combinations. Three-point bending tests with FRCs showed that the deposited SiO2 nanofilms effectively improved FRCs' strength and Group D underwent 100 deposition cycles and had the highest flexural strength before and after aging. Furthermore, the strength of the FRCs demonstrated a crescendo-decrescendo tendency with SiO2 nanofilm thickness increasing. The SBS results also showed that Group D had outstanding performance. Moreover, the results of cytotoxicity experiments such as cck8, LDH and Elisa, etc., showed that the FRCs have good cytocompatibility. Conclusion: Changing the number of ALD reaction cycles affects the mechanical properties of FRCs, which may be related to the stress relaxation and fracture between SiO2 nanofilm layers and the built-up internal stresses in the nanofilms. Eventually, the SiO2 nanofilms could enhance the FRCs' mechanical properties and performance to enamel by improving the interfacial bonding strength, and have good cytocompatibility.

Analytical Determination of Serotonin Exocytosis in Human Platelets with BDD-on-Quartz MEA Devices.

Amperometry is arguably the most widely used technique for studying the exocytosis of biological amines. However, the scarcity of human tissues, particularly in the context of neurological diseases, poses a challenge for exocytosis research. Human platelets, which accumulate 90% of blood serotonin, release it through exocytosis. Nevertheless, single-cell amperometry with encapsulated carbon fibers is impractical due to the small size of platelets and the limited number of secretory granules on each platelet. The recent technological improvements in amperometric multi-electrode array (MEA) devices allow simultaneous recordings from several high-performance electrodes. In this paper, we present a comparison of three MEA boron-doped diamond (BDD) devices for studying serotonin exocytosis in human platelets: (i) the BDD-on-glass MEA, (ii) the BDD-on-silicon MEA, and (iii) the BDD on amorphous quartz MEA (BDD-on-quartz MEA). Transparent electrodes offer several advantages for observing living cells, and in the case of platelets, they control activation/aggregation. BDD-on-quartz offers the advantage over previous materials of combining excellent electrochemical properties with transparency for microscopic observation. These devices are opening exciting perspectives for clinical applications.

Characterization of microplastics in outdoor and indoor air in Ranchi, Jharkhand, India: First insights from the region.

The study focused on detecting and characterizing microplastics in outdoor and indoor air in Ranchi, Jharkhand, India during post-monsoon (2022) and winter (2023). Stereo microscopic analysis showed that plastic fibres had a dominant presence, fragments were less abundant, whereas fewer films could be detected in indoor and outdoor air. The atmospheric deposition of microplastics outdoors observed 465 ± 27 particles/m2/day in PM10 and 12104 ± 665 and 13833 ± 1152 particles/m2/day in PM2.5 in quartz and PTFE, respectively during the post-monsoon months. During winter, microplastic deposition rates in PM10 samples were found to be 689 ± 52 particles/m2/day and 19789 ± 2957 and 30087 ± 13402 in quartz and PTFE particles/m2/day respectively in PM2.5. The mean deposition rate in indoor environment during post-monsoon was 8.3 × 104 and 1.03 × 105 particles/m2/day in winter. During the post-monsoon period in PM10, there were fibres from 7.7 to 40 µm and fragments from 2.3 µm to 8.6 µm. Indoor atmospheric microplastics, fibres ranged from 1.2 to 47 µm and fragments from 0.9 to 16 µm present respectively during the post-monsoon season. Fibres and fragment sizes witnessed during winter were 3.6-6.9 µm and 2.3-34 µm, respectively. Indoor air films measured in the range of 4.1-9.6 µm. Fourier transform infrared analysis showed that outdoor air contained polyethylene, polypropylene, Polystyrene, whereas indoor air had polyvinyl chloride. Polyethylene mainly was present in outdoor air, with lesser polypropylene and polystyrene than indoors, where polyvinyl chloride and polyethylene were in dominant proportions. Elemental mapping of outdoor and indoor air samples showed the presence of elements on the microplastics. The HYSPLIT models suggest that the particles predominantly were coming from North-West during the post-monsoon season. Principal component analysis indicated wind speed and direction influencing the abundance of microplastics. Microplastics concentration showed strong seasonal influence and potential to act as reservoir of contaminants.

Stabilization and strengthening effects of filamentous nanocellulose in the foam forming of quartz paper.

Compared with traditional papermaking, foam forming is a new papermaking technology that uses foam instead of water to disperse fibres, which can effectively solve the problem of poor evenness of ceramic paper, but the instability of foam itself affects the application of foam forming technology. Herein, a highly stable foaming agent for foam forming technology was prepared via physical reaction of lauryl dimethyl amine oxide (OB-2) with filamentous nanocellulose (cellulose nanofiber (CNF-C) and bacterial cellulose (BC)). Then, the quartz paper was prepared by foam forming technology. Firstly, hydrogen bond interactions between hydroxyl groups of the filamentous nanocellulose and hydrophilic moieties on OB-2 enabled the formation of a 3D nanonetwork layer on the surface of the bubble, which extended the half-life of the bubble and effectively prevented the bubble from bursting or coalescing. Then, the foam was extruded and cracked, and the filamentous nanocellulose was retained on the quartz fibres to prepare filamentous nanocellulose/quartz fibre paper by foam forming technology. The quartz paper exhibited excellent evenness and mechanical properties. In conclusion, the research of foam forming technology is of great significance to the application and development of special paper.

Study on the existing forms and recovery efficiencies of phosphorus in biochar from excess sludge.

With the background of carbon neutrality, the resource and energy utilization of excess sludge (ES) have become the focus of future research. The pyrolysis of ES can produce biochar and enrich phosphorus (P). In this paper, the existing forms and recovery efficiencies of P in biochar from ES (BCES) were investigated. The results showed that the total phosphorus (TP) content of BCES at 850 °C was 65.1 mg/g, and the inorganic phosphorus (IP) content was 64.2 mg/g. The TP content of BCES was two times heavier than that of ES. The main ingredient of ES was quartz (SiO2), while the main phases of BCES were quartz (SiO2) and aluminum phosphate (AlPO4) at 650 -850 °C, and P mainly existed in the form of AlPO4. When the pyrolysis temperature was 800 and 850 °C, two new minerals appeared: Ca5(PO4)3OH and CaZn2(PO4)2·2H2O. Based on the conditions of a leaching time of 150 min, a H2SO4 concentration of 0.2 mol/L, a stirring rate of 220 rpm and a liquid-solid ratio of 50 mL/g, the leaching efficiency of P in BCES was found to be 100%. The pyrolysis temperature had no effect on leaching efficiencies of P; however, a higher pyrolysis temperature promoted metal leaching content.

Phosphorus recovery from phosphate tailings through a two-stage leaching-precipitation process: Toward the harmless and reduction treatment of P-bearing wastes.

To achieve highly efficient extraction of phosphorus (P) and comprehensive utilization of phosphate tailings, a two-stage leaching-precipitation method was proposed. Phosphate tailings primarily consisted of dolomite, fluorapatite, and quartz. During the first-stage leaching, the large majority of dolomite was selectively dissolved and the leaching efficiency of Mg reached 93.1 % at pH 2.0 and 60 °C. The subsequent second-stage leaching of fluorapatite was performed and the P leaching efficiency was 98.8 % at pH 1.5 and 20 °C, while the quartz remained in the residue. Through two-stage leaching, a stepwise leaching of dolomite and fluorapatite was achieved. After chemical precipitation, calcium phosphate with a high purity of 97.9 % was obtained; and the total recovery efficiency of P exceeded 98 %. The obtained calcium phosphate can be a raw material in the phosphorus chemical industry, while the Mg-rich leachate and the final quartz-rich residue have the potential for Mg extraction and the production of mortars or geopolymers, respectively. The two-stage leaching-precipitation process could significantly reduce the leaching costs, and enhance the reaction rates. It is expected to realize a volume reduction and efficient resource utilization of the phosphate tailings by using this sustainable and promising solution.

An innovative method for the detection of alpha synuclein, a potential biomarker of Parkinson's disease: quartz tuning fork-based mass sensitive immunosensor design.

An innovative biosensing fabrication strategy has been demonstrated for the first time using a quartz tuning fork (QTF) to develop a practical immunosensor for sensitive, selective and practical analysis of alpha synuclein protein (SYN alpha), a potential biomarker of Parkinson's disease. Functionalization of gold-coated QTFs was carried out in 2 steps by forming a self-assembled monolayer with 4-aminothiophenol (4-ATP) and conjugation of gold nanoparticles (AuNPs). The selective determination range for SYN alpha of the developed biosensor system is 1-500 ng mL-1 in accordance with the resonance frequency shifts associated with a limit of detection of 0.098 ng mL-1. The changes in surface morphology and elemental composition were evaluated using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and energy-dispersive X-ray spectroscopy (EDX). The remarkable point of the study is that this QTF based mass sensitive biosensor system can capture the SYN alpha target protein in cerebrospinal fluid (CSF) samples with recoveries ranging from 92% to 104%.

Phyllite/bentonite mixture-an alternative effective buffer material for a geological disposal of radioactive waste.

The use of phyllite (Phy) instead of quartz in mixtures with bentonite (B) is recommended as a buffer material for engineering barriers in a geological repository of nuclear waste. The recommendation is based on experimentally determined sorption properties of various Phy/B mixtures. The adsorption capacity of Phy/B mixtures (Phy/B: 75/25, 50/50, and 25/75), the removal efficacy of Eu(III) ions (an analog for fissiongenic lanthanides and actinides), and the rate of their binding reaction were studied using the batch adsorption equilibrium and kinetic experiments at different Eu(III) initial concentrations, solution pH, and solution to adsorbent (L/S) ratio. The adsorption capacity of the Phy/B mixtures increased with the increased bentonite content in the mixture depending on the L/S ratio and solution pH. The highest increase in the adsorption capacity of the Phy/B mixtures compared to phyllite was observed for the Phy/B proportions of 25/75 and 50/50. The rate of the Eu(III) adsorption was the best fitted by the pseudo-second-order kinetic model indicating that the adsorption rate was controlled by chemisorption. The Sips model provided the best correlation of the adsorption experimental data, indicative of more than one adsorption site. The results of this study show the advantage of the Phy/B mixtures in immobilizing Eu and certain fission products by combining adsorption properties of the materials.

Determination of copper ion at trace levels in apple tea samples by simultaneous complexation and spray assisted microextraction method prior to detection by flame atomic absorption spectrophotometry.

In the present study, a green and sensitive analytical method for the determination of copper ion at trace levels in apple tea samples was developed. Simultaneous complexation/extraction of the analyte were achieved by spraying-based fine droplet formation liquid-phase microextraction (SFDF-LPME). Copper ion was complexed with a Schiff base chelating agent called as N,N'-Bis(salicylidene)-1,2-phenylenediamine (BSP). Under the optimum conditions, the developed SFDF-LPME-FAAS and FAAS system were assessed with respect to limit of detection (LOD), limit of quantitation (LOQ), linearity and percent relative standard deviation (%RSD). LOD and LOQ values for SFDF-LPME-FAAS method were found to be 6.0 and 19.9 µg/kg, respectively. Enhancement in calibration sensitivity for developed method was found as 23 folds. In addition, accuracy/suitability of the developed SFDF-LPME-FAAS method were confirmed by spiking experiments. Two different apple tea samples were spiked to different concentration values and percent recovery results from 91.1 and 123.8 % proved the accuracy/suitability of the method.

An experimental study of the effects of bacteria on asphaltene adsorption and wettability alteration of dolomite and quartz.

The adsorption of asphaltene on the rock surface and the changes in its wettability are very relevant issues in flow assurance and oil recovery studies, and for carbonate reservoirs, they are even more important. During microbial enhanced oil recovery (MEOR) processes, wettability alteration is considered a crucial mechanism leading to improved oil recovery. Therefore, it is essential to understand the mechanisms of surface wettability changes by bacteria and biosurfactants and find new and reliable methods to prevent asphaltene adsorption. Hence, the main aim of this research was to investigate the effect of a mixture of thiobacillus thiooxidans and thiobacillus ferooxidans microorganisms with an optimum effective temperature of around 30 °C (referred to as mesophilic bacteria), as well as a mixture of two moderate thermophiles Sulfobacillus thermosulfidooxidans for operating temperatures around 50 °C (referred to as moderately thermophilic bacteria) on the adsorption of asphaltene samples isolated from two different crude oils onto main reservoir minerals (i.e., quartz and dolomite). The results indicated that after two weeks of mineral aging in moderate thermophilic bacteria, the adsorption of asphaltene on both minerals increased between 180 and 290%. Fourier-transform infrared spectroscopy (FTIR) analysis for quartz and dolomite samples demonstrated that after aging in bacterial solution, bonds related to the adsorption of bacterial cells and biosurfactant production appear, which are the main factors of change in wettability. Alteration in wettability towards hydrophilicity expands hydrogen bonds on the surface, thus improving asphaltene adsorption due to polar interaction. Asphaltene 1 changed the contact angle of dolomite from 53.85° to 90.51° and asphaltene 2 from 53.85° to 100.41°. However, both strains of bacteria caused a strong water-wetting effect on the dolomite rock samples. The influence of moderate thermophilic bacteria on surface wettability is more significant than that of mesophilic bacteria, which may be caused by the high protein content of these bacteria, which expands hydrogen bonding with the surface. Adsorption of asphaltenes on dolomite rocks previously aged with bacteria showed that the wetted rock samples retained their water-wet state. This study highlights the dual impact of the used microorganisms. On one hand, they significantly reduce contact angles and shift wettability towards a strongly water-wet condition, a crucial positive factor for MEOR. On the other hand, these microorganisms can elevate the adsorption of asphaltenes on reservoir rock minerals, posing a potential challenge in the form of formation damage, particularly in low-permeability reservoirs.

Acetone Detection and Classification as Biomarker of Diabetes Mellitus Using a Quartz Crystal Microbalance Gas Sensor Array.

A gas sensor array was developed and evaluated using four high-frequency quartz crystal microbalance devices (with a 30 MHz resonant frequency in fundamental mode). The QCM devices were coated with ethyl cellulose (EC), polymethylmethacrylate (PMMA), Apiezon L (ApL), and Apiezon T (ApT) sensing films, and deposited by the ultrasonic atomization method. The objective of this research was to propose a non-invasive technique for acetone biomarker detection, which is associated with diabetes mellitus disease. The gas sensor array was exposed to methanol, ethanol, isopropanol, and acetone biomarkers in four different concentrations, corresponding to 1, 5, 10, and 15 µL, at temperature of 22 °C and relative humidity of 20%. These samples were used because human breath contains them and they are used for disease detection. Moreover, the gas sensor responses were analyzed using principal component analysis and discriminant analysis, achieving the classification of the acetone biomarker with a 100% membership percentage when its concentration varies from 327 to 4908 ppm, and its identification from methanol, ethanol, and isopropanol.

Origin, formation, and transformation of different forms of silica in Xuanwei Formation coal, China, and its' emerging environmental problem.

The study on the origin of quartz and silica in Xuanwei Formation coal in Northwest Yunnan, China, is helpful to understand the relationship between quartz and silica and the high incidence of lung cancer from the root. To address these questions, the mineralogy and microscopic studies of silica in Xuanwei Formation coal were performed. The following results were obtained: (1) silica in the late Permian Xuanwei Formation coal seams originated from detrital input, early diagenesis, and late diagenesis. (2) A more significant contribution comes from early diagenesis, which contains abundant authigenic quartz and amorphous silica. (3) Quartz and silica from inorganic silicon are more symbiotic with kaolinite and from biogenic silicon with chamosite. (4) Three silica polymorphs in coal samples have been identified: opal-A (amorphous silica), opal-CT/-C (cristobalite/tridymite), and α quartz. (5) Opal-A is ubiquitous, while opal-CT/-C and α quartz are rare. (5) Opal-A is an amorphous and nontoxic ordinary silica. (6) Since the toxicity of amorphous silica and its presence in coal is an emerging topic, it should be continuously monitored.

Impact of vacuum ultraviolet (VUV) intensity on the performance of VUV irradiation for the mineralization of trimethoprim in neutral media: Kinetics, mechanisms, and by-products formation.

A comparative study on the mineralization of antibiotic trimethoprim (TMP) in neutral medium was investigated by applying irradiation with five types of ultraviolet lamps. Among these lamps, the whole envelope of one lamp contained ordinary quartz, which could only transmit ultraviolet-C (UVC) light. For the other four lamps, approximately one tenth, a quarter, a half, and full of envelopes were comprised of high-purity synthetic quartz, which can transmit both vacuum ultraviolet (VUV) and UVC light. TMP decay was well fitted to pseudo-first-order reaction kinetics and occurred more quickly as the VUV intensity increased. Poor mineralization was achieved in the absence of VUV light, whereas the mineralization efficiency was also enhanced with increasing VUV intensity. The presence of hydroxyl radicals (•OH), superoxide radicals (O2•-) and singlet oxygen (1O2) during VUV photolysis of water was confirmed by electron paramagnetic resonance (EPR) analysis. Appropriate radical quenching experiments and fluorescent molecular probe detection provided the evidence that •OH played a significant role in TMP mineralization. Higher VUV intensity favored the generation of H2O2 and •OH. The evolution of NH4+ and NO3- as well as carboxylic acids (formic, acetic, oxalic, and oxamic acids) released in the treated solution were quantified. Ten aromatic intermediates were also identified by UPLC-QTOF-MS. Thereby, a plausible reaction sequence for TMP mineralization in VUV/UVC photolysis was finally proposed.

Real-Time Evaluation of Adhesion Processes and Glucose Response of Cancer Cells onto Phenylboronic Acid-Functionalized Films Monitored by Quartz Crystal Microbalance with Dissipation.

Understanding the interactions between cancer cells and smart substrates is of great benefit to physiology and pathology. Herein, we successfully fabricated two phenylboronic acid (PBA)-functionalized films with different surface topographies using a PBA homopolymer (PBAH) and self-assembled nanoparticles (PBAS) via a layer-by-layer assembly technique. We used a quartz crystal microbalance with dissipation (QCM-D) to monitor the entire cell adhesion process and figured out the adhesion kinetics of HepG2 cells on the two PBA-functionalized films. As seen from the QCM-D data, the HepG2 cells displayed distinctly different adhesion behaviors on the two PBA-functionalized films (PBAS and PBAH films). The results showed that the PBAS film promoted cell adhesion and cell spreading owing to its specific physicochemical properties. Likewise, the slope changes in the D-f plots clearly revealed the evolution of the cell adhesion process, which could be classified into three stages during cell adhesion on the PBA-functionalized films. In addition, compared with the PBAH film, the PBAS film could also control cell detachment behavior in the presence of glucose based on the molecular recognition between the PBA group and the cell membrane. Such a glucose-responsive PBAS film is promising for biological applications, including cell-based diagnostics and tissue engineering. In addition, the QCM-D proved to be a useful tool for in situ and real-time monitoring and analysis of interactions between cells and surfaces of supporting substrates.

Mercury determination in various environmental, food and material complex matrices using unified operating conditions for a cold vapor generation high-resolution continuum source quartz tube atomic absorption spectrometry method.

An analytical method with broad applicability based on cold vapor generation high-resolution continuum source quartz tube atomic absorption spectrometry was developed and evaluated for the determination of total mercury in matrices with various complexities and compositions. Sample preparation for different matrices of food, environmental samples and (bio)polymeric materials and unified operating conditions for derivatization and measurement were evaluated. The method was validated according to established requirements (Eurachem Guide 2014, EC Decisions 657/2002; 333/2007; 836/2011 and Association of Official Analytical Chemists Guide - AOAC). Analytical versatility was checked on various samples of fish fillets, mushrooms, soil, water and water sediment, sludge from a wastewater treatment unit, and (bio)polymeric materials from waste recycled from food packaging, computers and garden tools. Under optimal conditions for cold vapor generation in a batch system, namely 3% (v/v) HCl as reaction medium for 5 mL aliquot samples and a volume of 3.5 mL 0.3% (m/v) NaBH4 stabilized in 0.2% (m/v) NaOH as derivatization reagent, the detection limit for Hg in terms of peak height measurement (n = 7 days) was in the range 0.064 ± 0.004 µg L-1 in water, 0.014 ± 0.001 mg kg-1 in environmental samples and 0.009 ± 0.001 mg kg-1 in (bio)polymeric materials. Overall recovery of Hg by analysis of certified reference materials was 102 ± 20% (k = 2) in food, soil, wastewater and water sediment, and polyethylene. Precision for the measurement of various real samples ranged between 4.2 and 15.0%. A performance study highlighted that the method was sensitive, free of non-spectral interference coming from the multielemental matrix and that it complied with the requirements for Hg determination set in EC Decisions and AOAC Guidelines at least for the more common matrices analyzed for social impact.